Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NCSIE ONTAP

Question - 14 Maximum mark : - 27

Home
All Exams
Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NCSIE ONTAP Online Practice Exams
Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NCSIE ONTAP

What is the main function of ACP?

It allows cabling the shelf to two additional controllers. ✘ It allows the controller to use Ethernet instead of SAS to fetch the storage data. ✘ It allows the controller to nondisruptively reset the SAS expanders. ✘ It enables the automatic shelf ID assignment. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You want to expand an existing FAS8060 switchless cluster running ONTAP 9.1 with an AFF A300 system.
Which action should you take to perform this task?

Execute the cluster setup command on the existing FAS8060 cluster, add the cluster interconnect switches, and cable both the FAS8060 cluster and the
AFF A300 system to the new cluster. ✘ Create a separate switchless cluster with the AFF A300 system. ✘ Connect the cluster ports of the AFF A300 system to the existing FAS8060 cluster, and join the existing cluster. ✘ Add and configure the cluster interconnect switches, re-cable the FAS8060 cluster, add the AFF A300 system, and join the existing cluster. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

A customer has a stack of shelves with both DS4243 shelves and DS4246 shelves. The customer wants to replace the DS4243 shelves with new DS4246 shelves.
What would you advise the customer in this scenario?

Convert the ACP communication from out-of-band to in-band channel. ✘ Remove the ACP cabling from the stack before adding the new shelves. ✘ Remove the DS4243 shelves, but you must add the new DS4246 shelves to a new stack. ✘ Configure the shelf IDs of the new DS4246 shelves to match the existing DS4246 shelves. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Without adding new cluster interconnect switches, you want to nondisruptively upgrade from FAS2554 controllers to FAS8200 controllers on an existing 2-node switchless cluster running ONTAP 9.1 software.
Which statement is correct in this scenario?

Relocate the aggregates to one FAS2554 node, takeover, replace the node in takeover state with a FAS8200 node, reassign the disks, giveback, and repeat for
the second node. ✘ Connect the FAS8200 to the FAS2554 with interconnect cables, join the existing cluster, relocate the aggregates from the FAS2554 to the FAS8200, anddecommission the FAS2554. ✘ Set up the FAS8200 as a new cluster, move the SVMs from the FAS2554 to the FAS8200 using SVM move, and decommission the FAS2554. ✘ You cannot perform this task nondisruptively. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You have just installed a new FAS2650 HA for your customer. You are now configuring the NetApp AutoSupport transport section.
In this scenario, what is the NetApp best practice for this task to allow AutoSupport on Demand (ASOD)?

Use SMTP. ✘ Use HTTPS. ✘ Use HTTP. ✘ Use SSH. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

After an installation, your customer asks you if you have a solution or a product that can easily list all the elements of a running ONTAP cluster, and highlight the changed and new objects including IP addresses, subnets, IPspaces, SVMs, volumes, and LUNs. For easy modification the output should be a document or a spreadsheet. Your customer does not have any PowerShell or scripting knowledge.
In this scenario, which Windows PowerShell-based NetApp tool would help to extract this information?

NetApp Management SDK ✘ NetAppDocs ✘ NetApp PowerShell Toolkit ✘ NetApp Synergy ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs.
Which statement is correct in this scenario?

Prior to leaving the site, tell the customer that a later firmware exists for those disk drives, but that the upgrade will provoke downtime. ✘ Unless the customer advises otherwise, upgrade the firmware on the SSDs to clear the Config Advisor error. ✘ Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded. ✘ Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You finished an ONTAP 9.1 installation using the information provided by the customer, but the NFS exports and CIFS shares cannot be accessed using the newly created data LIFs.
In this situation, which action should you perform before you leave the customer's site?

Advise the customer to but Cisco switches because NetApp supports only Cisco switches for CIFS and NFS. ✘ Review the ONTAP network configuration with the customer and make sure that it is correct. ✘ Connect to the customer's switch infrastructure and reset the port configurations. ✘ Advise the customer to solve the issue on their own, this is not part of a basic installation. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You install a new AFF A300 2-node switchless cluster with ONTAP 9.1 at a customer site. Each node has a root aggregate as part of the system configuration.
In this scenario, what is the default disk partitioning called?

root-data-data partitioning ✘ data-data partitioning ✘ root-data partitioning ✘ root-data-root partitioning ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

10.

You are configuring a new system with ONTAP 9.1. You created interface groups, VLANs, and a broadcast domain for the new ports on all the nodes of your cluster. During the configuration, you used an MTU value of 1500 for the broadcast domain and 9000 for the physical ports. The customer asks you to enable jumbo frames.
What should you do in this scenario?

Set the MTU option to jumbo frames on the broadcast domain. ✘ Change the MTU value to 9000 on the ifgroup. ✘ Set the MTU option to jumbo frames on the ifgroup. ✘ Change the MTU value to 9000 on the broadcast domain. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Prev Next

Congratulations

you have successfully completed the test

Back to Question View Result

Detail Form

We will send your result on your email id and phone no. please fill detail

Name

Email ID Note: Report will be send to the above Email ID

Phone No

Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NCSIE ONTAP

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner