Juniper Networks Certified Internet Associate WX (JNCIA-WX) Set 2

1.

Which action occurs when a WX device is configured for the hub-and-spoke topology?

The meshed devices send memory allocation parameters to the spoke devices. The reduction setting of "Only checked WX devices below" cannot be checked. All spoke devices default to the reduction setting of "Only WX devices designated as hubs". Spoke-to-spoke communications are no longer available.

2.

Which statement about the WebView submit command is true?

The submit command exits the GUI. The submit command is the same as the commit CLI command. The submit command reboots the WX device. The submit command saves and writes the configuration to flash.

3.

What are two ways to verify if a WX device is configured as a hub, a spoke or a mesh device? (Choose two.)

Reduction > Endpoints Setup > Advanced > Features/Topology Admin > Device Setup > Features/Topology

4.

Microsoft's file sharing, Microsoft's e-mail, and Web browsing is performed in Customer A's network. Customer B uses its network for only Citrix traffic. Which two solutions satisfy both customers? (Choose two.)

PFA and AppFlow for Customer B PFA for Customer A PFA and AppFlow for Customer A PFA for Customer B

5.

How does a WX device use local routes to determine whether a reduction subnet is valid?

It checks whether the local route's gateway is on the LAN side. It checks whether the default gateway is on the WAN side. It checks whether the default gateway is on the LAN side. It checks whether the local route's gateway is on the WAN side.

6.

Which features must be enabled to configure AppFlow for Outlook on the WXC device?

AppFlow, QoS, AFP, Application definition, MAPI AppFlow, HTTP, Application definition, Multipath AppFlow, QoS, FEC, Application definition, CIFS AppFlow, Exchange, Application definition, FCS

7.

What is one way to escape hardware bypass mode?

Set the device to factory default. Power cycle the device. Reboot the device from the console. Bounce the tunnel.

8.

Which option describes the main difference between the WX and WXC platforms?

WXC platform has no built-in hard drives. WX platform has built-in hard drives. WXC platform uses the Network Sequence Caching technology. WX platform uses Network Sequence Caching technology.

9.

Which statement is true regarding SMB signing and AppFlow CIFS acceleration?

If SMB signing is off, then CIFS acceleration will be performed. SMB authenticates the WX reduction tunnel, allowing CIFS acceleration to be accomplishedsuccessfully. If SMB signing is on, then CIFS acceleration will be performed. SMB assigns hash values to the packet, allowing CIFS acceleration to take place.

10.

What is the recommended method to configure outbound QoS?

Use the Setup Wizard. Enable 802.1q. Use direct setup. Use command-line interface.

Juniper Networks Certified Internet Associate WX (JNCIA-WX) Set 2

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Juniper Networks Certified Internet Associate WX (JNCIA-WX) Set 2

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner