HP BladeSystem Networking Set 3

1.

Which switching technology is a software virtualization technology that allows the connection of multiple physical switches to form a single virtual switch in either a ring or bus configuration?

Cisco Virtual Port Channel (vPC) Cisco Virtual Switching System (VSS) HP Intelligent Resilient Framework (IRF) HP ProCurve Distributed Trunking (DTP)

2.

A user connects a laptop to Port 6 of a network switch and has access to VLAN 10 resources and the Internet. Several minutes later, the user connects a similarly configured laptop to the same port, and has access to VLAN 11 resources, but no Internet access.What can cause this to occur?

A static ACL is set up for the user that controls VLAN and Internet access permissions for each device the user attempts to connect with. Each laptop connection is monitored to determine the type of VLAN and Internet access allowed and user access parameters. The default VLAN is incorrectly configured on one or both laptops or connected switch port. A dynamic ACL is defined on the switch port that uses a RADIUS server and the laptops MAC addresses to determine VLAN and Internet accesspermissions.

3.

Which HP Virtual Connect feature provides functionality similar to an industry-standard trunk?

aggregated switch links tagged VLAN port (802.1Q) tagged VLAN port plus link aggregation Shared Uplink Set plus Connection Mode Auto

4.

A customer plans to manage Virtual Connect Fibre Channel modules in a domain. Why is a Virtual Connect Ethernet module required?

Virtual Connect Manager software is embedded on the Virtual Connect Ethernet module. Virtual Connect Fibre Channel modules are not stand-alone devices and rely on Virtual Connect Ethernet module circuitry for operation. Virtual Connect Fibre Channel modules use the routing engine of the Virtual Connect Ethernet module for FCoE traffic. The management IP address for the Virtual Connect Fibre Channel modules is only accessible through a Virtual Connect Ethernet module.

5.

What is a benefit of dynamic link aggregation?

Port VLAN membership is transferred to a dynamic trunk. Dynamic links support HP port trunking. Dynamic standby links are supported. Dynamic links appear in the switch configuration file.

6.

Which statement is correct about a Shared Uplink Set?

It is the only uplink type that allows tagged and untagged VLANs. It is the only construct that allows uplinks to form a trunk. It is a connecting point for vNets that share server downlink ports. It allows a set of uplinks to be shared by multiple VLANs.

7.

What allocates bandwidth across the FlexNICs in an HP Virtual Connect Flex-10 environment?

The Virtual Connect Manager or Virtual Connect Enterprise Manager monitors the utilization of each FlexNIC and dynamically adjusts bandwidth
accordingly. When the Windows Server 2008 operating system is loaded, each FlexNIC has its own driver. Right-clicking on the icon enables you to set theindividual bandwidth. When the Virtual Connect Flex-10 Ethernet module and Onboard Administrator (OA) discover the FlexNICs, bandwidth is allocated using the OA. The Virtual Connect Manager or Virtual Connect Enterprise Manager Server Profile construct is used to manage each FlexNIC and configure itsbandwidth.

8.

What is the SNTP protocol used for?

file transfer address resolution time synchronization loop prevention

9.

Bridge priority is at the default value in a spanning tree environment. Which parameter do you use to elect the Root bridge?

Root Enable parameter MSTP version number switch MAC address lowest-cost switch path

10.

A server profile has been defined where the total custom and preferred bandwidth values specified for the server's FlexNICs exceed 10Gb.How does Virtual Connect Manager handle this situation?

It allocates the requested bandwidth to each FlexNIC, starting with the lowest numbered port until the entire 10Gb has been assigned. The remaining ports are disabled. It calculates the proportion of the total each FlexNIC has been allocated and assigns each an equal proportion of the available 10Gb. It forces the bandwidth values to be re-entered until the total requested does not exceed the 10Gb available. It returns an error and requires the deletion and re-creation of the server profiles that have been defined across all the enclosures in the domain.

HP BladeSystem Networking Set 3

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

HP BladeSystem Networking Set 3

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner