CWNP Certified Wireless Network Administrator Set 2

1.

When device mobility mode is enabled or disabled for a cluster, to which does the cluster setting apply?

Minimum output power level of 2 W Accurate Earth Bulge calculations Grid antennas at each endpoint A minimum antenna gain of 11 dBi at both endpoints A Fresnel Zone that is at least 60% clear of obstructions

2.

Which statement is true when device mobility mode is enabled or disabled in the Phone Configuration window?

The power output from the radio into the RF cable The power output from the radio after cable losses The highest RF signal strength that is transmitted from a given antenna Reflected power due to an impedance mismatch in the signal path Power supplied from the transmission line to the antenna input

3.

With Cisco Extension Mobility, when a user logs in to a phone type which has no user device profile, what will happen to the phone?

Distributed Radiation Active Amplification Beam Compression Passive Gain RF Flooding

4.

Which statement about H.323 Gatekeeper Call Admission Control is true?

Dipole Patch Dish Grid Sector

5.

Which statement is correct about AAR?

Alternates between awake and dozing, depending on its need to transmit and receive information Enters a low-power radio state until it receives a WMM PS-Poll frame from the AP Experiences higher throughput and lower latency than when operating in Active mode Powers down a subset of MIMO radio chains and transmits information at a slower data rate Buffers frames destined to the low-power AP until the AP wakes its radio and begins beaconing again

6.

The relationship between a Region and a Location is that the Region codec parameter is used between a Region and its configured Locations.

Beam width Range Active gain Receive sensitivity Fresnel Zone size

7.

The relationship between a Region and a Location is that the Region codec parameter is combined with Location bandwidth when communicating with other Regions.

The lower the gain of an antenna, the more narrow one or both beamwidths become. The beamwidth patterns on an antenna polar chart indicate the point at which the RF signal stops propagating. Horizontal and vertical beamwidth are calculated at the points in which the main lobe decreases power by 3 dB. Horizontal beamwidth is displayed (in degrees) on the antenna's Azimuth Chart.

8.

You are deploying a remote office setup that connects with Cisco Unity Communications Manager at a hub location. You have an available dedicated bandwidth of 20% from the 2-Mb/s WAN circuit for VoIP that supports a maximum of 17 calls. Which codec do you configure in Cisco Unity Communications Manager to achieve this?

Spatial multiplexing Short guard intervals Maximal ratio combining Orthogonal Frequency Division Multiplexing

9.

Which task must you perform before deleting a transcoder?

Fresnel Zone size Maximum input power Beamwidth Impedance VSWR Ratio

10.

Which action configures PSTN backup for calls that are rejected by the gatekeeper CAC?

One spatial stream, because the definition of the AP indicates that it is capable of only one spatial stream. Three spatial streams, because the definition of the client indicates that it is capable of only three spatial streams. Two spatial streams, because the definition of the AP indicates that it is capable of only two spatial streams. Three spatial streams, because the definition of the AP indicates that it is capable of only three spatial streams.

CWNP Certified Wireless Network Administrator Set 2

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

CWNP Certified Wireless Network Administrator Set 2

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner