CWNP Certified Wireless Network Administrator Set 1

1.

What user profile is used to define the settings for a user on login?

The client station transmits a Reassociation Request frame to its current access point. The current access point informs the IP gateway of the reassociation. The current access point triggers the client's reassociation service. The new access point transmits a Reassociation Response to the client station with a status value. The client and new access point create unicast encryption keys.

2.

Which statement about technology implementation strategy is true?

The current AP is using channel 1 and the new AP is using channel 40. The SSID of the current AP does not match the SSID of the new AP. The current AP supports only HT and the new AP is VHT capable. The access points are hiding the SSID in Beacons and Probe Response frames.

3.

Which commands are needed to configure Cisco Unified Communications Manager Express in SRST mode?

The SSID is a security session identifier used in RSNs. The SSID must be included in an association request frame. The SSID is an alphanumeric value assigned to device manufacturers by the IEEE. The SSID is a pseudo-random number assigned to each client by an AP. The SSID is an alphanumeric value with a maximum length of 32 octets.

4.

What command is used to map internal extensions to the corresponding E.164 PSTN number when using Cisco Unified Communications Manager Express in SRST mode?

An IBSS does not have a distribution system (DS), but a BSS does. An IBSS does not require beacon frames, but a BSS does. An IBSS does not support 802.11 authentication or association, but a BSS does. An IBSS does not support any 802.11ac enhancements, but a BSS does.

5.

Which statement about enrollment in the IP telephony PKI is true? (Source. Understanding Cisco IP Telephony Authentication and Encryption Fundamentals)

A single AP supports multiple BSSs with different SSIDs A virtual cell single channel network has been implemented The beacons are from an IBSS instead of a BSS Three APs still share the same default configuration.

6.

In what Cisco solution is Simple Network-Enabled Auto Provision technology used?

Multipath will increase, causing excessive layer-2 retransmissions. The retransmissions will cause latency for VoWiFi handsets. Increased receiver sensitivity on the VHT APs will cause them to continually change channels to avoid co-channel interference. If the existing UTP cabling is not Category 3 or better, the total Ethernet backhaul for each AP will be limited to 100 Mbps. The existing WLAN plan, including the AP locations, may not provide the benefits seen in HT and VHT 802.11 PHY capabilities.

7.

While configuring Call Survivability in Cisco Unified Communications Manager, what step is mandatory to reach remote sites while in SRST mode?

Aesthetic requirements Physical security and theft prevention Protection from environmental conditions Reduce transient RF interference 802.11 security compliance

8.

While operating in SRST, what is needed to route calls outside of the remote site location to the PSTN?

Large 802.11 cells with physically distributed stations Client stations broadcasting with too much power Access points broadcasting with too little power Client stations too close in proximity to each other Obstacles between client stations causing attenuation

9.

When using Cisco Unified Communications Manager Express in SRST mode, how many multicast music on hold streams can be utilized by the system at any given time?

The direct signal will only be received if the reflected signal is more than 180 degrees out of phase. The direct signal cannot be received if the indirect signal is less than 90 degrees out-of-phase. The signals will be distorted if the indirect signal arrives simultaneously at the receiver, but 90 degrees out-of phase. If the signals are in-phase, they will combine together, cancel one another out, and create a null.

10.

What is the fastest way for an engineer to test the implementation of SRST in a production environment?

The access points are mounted too closely to one another. Reflective objects in the area are causing significant multipath. A client station is using active scanning to probe for access points on multiple channels. The output power on the access points is too high. A client station authenticates to both access points, but does not associate.

CWNP Certified Wireless Network Administrator Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

CWNP Certified Wireless Network Administrator Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner