Citrix-Implementing NetScaler 10 for Networking and Traffic Optimization Set 1

1.

Which command can be used to view NAT statistics per IP pool on the Cisco ASR 5000??

Reset the nsroot account. Change the nsroot password. Create an authorization policy. Bind a policy to the root user account.

2.

What does the X-Header Insertion feature on the Cisco ASR 5000 enable the operator to do?

TCP Buffering Use Source IP Edge Configuration MAC based forwarding

3.

Where are EDR records stored by default on the Cisco ASR 5000?

FIS PBR SNMP VMAC

4.

What protocol is used to initiate a PPP negotiation between Mobile and PDSN?

Reset the unused interfaces Disable the unused interfaces Enable flow control on all interfaces Disable HA monitoring on the three interfaces that are no longer required

5.

What network element executes bearer binding in a PMIPv6 LTE network?

Create an IPv6 tunnel and a IPv4 virtual server. Configure an IPv6 VLAN and bind the required interface. Create a IPv4 virtual server and bind the service group to it. Create an IPv6 ACL and a IPv4 virtual server and bind the ACL to the virtual server.

6.

Which network element sends the Re-Auth-Request?

Disable static route advertisement. Disable layer 2 modeCreate 2 untagged VLANs - VLAN 2 and VLAN 3
Bind VLAN 2 to Interface 1/1
Bind VLAN 3 to Interface 1/2 Enable Layer 3 modeCreate a Channel Interface using Interface 1/1 and 1/2 Create 2 VMACs
Bind a VMAC to interface 1/1 and 1/2 Configure policy-based routing using the Interface option as a filter.

7.

Which option best describes Attribute-based tunneling on the Cisco ASR 5000?

To enable use of features like SSL over TCP for that specific service group. To adjust the TCP settings for traffic to and from that specific service group. To use a specific SNIP for traffic to the back-end servers in that service group. To enable features like use source IP, TCP keep alive and TCP buffering for a specific service group.

8.

Which describes NEMO-Tunnel on HA?

/nsconfig/ssl /nsconfig/ssh flash/nsconfig/ /var/netscaler/ssl/

9.

Where is ECS rulebase referenced on the Cisco ASR 5000 PDSN in order to apply rules defined in active-charging service?

set ns ip 10.20.30.40 -gui disabled -telnet disabled set ip 10.20.30.40 -gui secureonly -mgmtaccess enabled set ip 10.20.30.40 -mgmtaccess disabled -gui secureonly set ns ip 10.20.30.40 -gui enabled -restrictAccess enabled

10.

What three conditions will the target HSGW initiate authentication as soon as possible to continue with the session for stage 3 inter-HSGW handoff? (Choose three.)?

Create an Extended ACL based on the source IP address. Create a restricted route from the internal network to the DMZ. Enable the management access control option on the NSIP address. Enable the management access control on the internal SNIP address.

Citrix-Implementing NetScaler 10 for Networking and Traffic Optimization Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Citrix-Implementing NetScaler 10 for Networking and Traffic Optimization Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner