×
Detail Form
We will send your result on your email id and phone no. please fill detail
1.
You are troubleshooting a site-to-site VPN issue where the tunnel is not establishing. After issuing the debug crypto ipsec command on the headend router, you see the following output. What does this output suggest?
1d00h: IPSec (validate_proposal): transform proposal (port 3, trans 2, hmac_alg 2) not supported
1d00h: ISAKMP (0:2) : atts not acceptable. Next payload is 0 1d00h: ISAKMP (0:2) SA not acceptable
1d00h: ISAKMP (0:2) : atts not acceptable. Next payload is 0 1d00h: ISAKMP (0:2) SA not acceptable
2.
Which adaptive security appliance command can be used to see a generic framework of the requirements for configuring a VPN tunnel between an adaptive security appliance and a Cisco IOS router at a remote office?
3.
After completing a site-to-site VPN setup between two routers, application performance over the tunnel is slow. You issue the show crypto ipsec sa command and see the following output. What does this output suggest?
interfacE. Tunnel100
Crypto map tag: Tunnel100-head-0, local addr 10.10.10.10
protected vrF. (none)
local ident (addr/mask/prot/port): (10.10.10.10/255.255.255.255/47/0) remote ident (addr/mask/prot/port): (10.20.20.20/255.255.255.255/47/0) current_peer
209.165.200.230 port 500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 34836, #pkts encrypt: 34836, #pkts digest: 34836 #pkts decaps: 26922, #pkts decrypt: 19211, #pkts verify: 19211 #pkts compresseD. 0, #pkts
decompresseD. 0
#pkts not compresseD. 0, #pkts compr. faileD. 0
#pkts not decompresseD. 0, #pkts decompress faileD. 0 #send errors 0, #recv errors 0
Crypto map tag: Tunnel100-head-0, local addr 10.10.10.10
protected vrF. (none)
local ident (addr/mask/prot/port): (10.10.10.10/255.255.255.255/47/0) remote ident (addr/mask/prot/port): (10.20.20.20/255.255.255.255/47/0) current_peer
209.165.200.230 port 500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 34836, #pkts encrypt: 34836, #pkts digest: 34836 #pkts decaps: 26922, #pkts decrypt: 19211, #pkts verify: 19211 #pkts compresseD. 0, #pkts
decompresseD. 0
#pkts not compresseD. 0, #pkts compr. faileD. 0
#pkts not decompresseD. 0, #pkts decompress faileD. 0 #send errors 0, #recv errors 0
4.
Which Cisco adaptive security appliance command can be used to view the count of all active VPN sessions?
5.
To change the title panel on the logon page of the Cisco IOS WebVPN portal, which file must you configure?
6.
Which command simplifies the task of converting an SSL VPN to an IKEv2 VPN on a Cisco ASA appliance that has an invalid IKEv2 configuration?
7.
Which statement describes a prerequisite for single-sign-on Netegrity Cookie Support in an IOC SSL VPN?
8.
Which command enables IOS SSL VPN Smart Tunnel support for PuTTY?
9.
Which command will prevent a group policy from inheriting a filter ACL in a clientless SSL VPN?
10.
Which command specifies the path to the Host Scan package in an ASA AnyConnect VPN?