Cisco-Implementing Cisco Unified Wireless Mobility Services Set 1

1.

Which Cisco ASA configuration is used to configure the TCP intercept feature?

24 controllers with up to 2,400 APs 24 controllers with up to 3,600 APs 72 controllers with up to 8,700 APs 72 controllers with up to 10,800 APs

2.

Which configuration step (if any) is necessary to enable FTP inspection on TCP port 2121?

RF group leader connected controller internal logic of the access point AP neighbor messages

3.

When the Cisco ASA appliance is processing packets, which action is performed first?

every 60 seconds every 90 seconds every 180 seconds by default and can be adjusted every time the AP does off-channel measurement

4.

Which Cisco ASA (8.4.1 and later) CLI command is the best command to use for troubleshooting SSH connectivity from the Cisco ASA appliance to the outside 192.168.1.1 server?

received voice RSSI at -73dBm for 5 seconds received data RSSI from a client at -80dBm for 3 seconds received data RSSI from three clients at -74dBm for 5 seconds one associated client had data received at -77 dBm for 3 seconds

5.

On which type of encrypted traffic can a Cisco ASA appliance running software version 8.4.1 perform application inspection and control?

Cisco WCS should be installed in the same location on the new server as it was on the previous server. The previous Cisco WCS server should have the "WCS Server Backup" background task enabled so adatabase backup may be retrieved. Re-install the older Cisco WCS and perform a manual backup as only the backups that are performedmanually can be used for recovering the data. Enable the "Mirror WCS" background task on the older Cisco WCS to replicate database to the new CiscoWCS.

6.

Where in the Cisco ASA appliance CLI are Active/Active Failover configuration parameters configured?

Device Status Configuration Sync Mobility Service Backup Controller Configuration Backup

7.

With Cisco ASA active/active or active/standby stateful failover, which state information or table is not passed between the active and standby Cisco ASA by default?

setting and applying mobility group name rebooting Cisco WLCs in a cascading manner setting and applying channel width setting and applying Cisco WLC multicast mode scheduling configuration templates

8.

Which Cisco ASA object group type offers the most flexibility for grouping different services together based on arbitrary protocols?

Make one configuration group per building, add respective controllers, set the primary, secondary, tertiary controller values, and apply templates. Make a lightweight AP template, set the primary, secondary, tertiary controller values, andapply templatesby searching for APs by location. Make a separate template for each AP and apply based on the AP's location. Make a lightweight AP template, set the primary, secondary, tertiary controller values, and apply templatesby searching for APs by AP model.

9.

Which item is the best practice to follow while restoring archived data to a Cisco Security MARS appliance?

to create IP address groups that are used to allow management access to the Cisco WLC to create IP address groups that are used to assign addresses to clients via the Cisco WLC DHCP Server to create IP address groups that are used in access control lists to create IP address groups of AAA authentication and accounting servers

10.

What is the reporting IP address of the device while adding a device to the Cisco Security MARS appliance?

AP must be loaded with recovery image first. AP Telnet credentials must be privilege level 0. AP should be running a minimum software version of 12.3(7)JA. AP should be in bridge or repeater mode.

Cisco-Implementing Cisco Unified Wireless Mobility Services Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Cisco-Implementing Cisco Unified Wireless Mobility Services Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner