Cisco Implementing Cisco TelePresence Installations (ITI) Set 1

1.

Which would be considered the best environment to house a dedicated Cisco TelePresence system?

a conference room in the corner of a building with the best view a conference room next to the elevator for easy accessibility a conference room along an interior corridor an open space in the demonstration area of a briefing center a large meeting room used for events

2.

What are two Cisco recommendations when a customer has magnetic ballast installed in?

Enable auto brightness and disable auto color balance. Enable auto brightness and auto color balance. Enable 50-Hz flicker reduction Enable focus distance to A feet Replace the light fixture with an electronics fixture

3.

When booting the Cisco TelePresence 500, how do you determine which IP address is used by the codec before connecting to the codec via WebGUI?

The codec, uses 10.1.1.1 as its default IP setting The IP address is displayed on the phone user interface The IP address is displayed during the hunt process on the plasma The codec uses 192.168.300.2 as its default IP setting

4.

When using the camera target on a Cisco TelePresence System 1300, how often do you need to repeat the auto-adjust procedure before all cameras are calibrated?

once twice three times four times

5.

Which statement is correct when discussing the Cisco Telepresence System 500?

Installation is easy with some required remediation and construction cost A power distribution unit provided with the system The system requires three AC outlets one tor the codec, one for the facade lighting, and one for the LCDdisplay The system requires two AC outlets one for the codec and one for the LCD display

6.

Which statement is correct when discussing the camera target placement for the Cisco Telepresence System 500?

Do not set the easel and large target in the position that the user will occupy Use the distance measured from the camera to the head of the user to position the target If the distance isunknown, use 1.5 meters (5 feet) The user must be at least 8 feet (2,4 meters) away from the display Raise or lower the target so that the green rectangle that displays on the screen is at the approximate eyelevel of the user

7.

Which side of the cabinet is the Cisco Telepresence System 1100 and 1300 codec inserted?

right center left back and center

8.

How many camera processors does the Cisco Telepresence System 1300 have?

one two three four

9.

How should directory number of the phone and the Cisco Telepresence endpoint be configured in the Cisco Unified CallManager?

As a shared line where the codec and IP phone share the same directory number As a single line for the codec and a single line for the phone using the same directory number. As an overlay line using the same directory number As a single line for the phone and it only has a directory phone number. The codec uses the IP address ofthe phone

10.

What are three requirements to tune the camera properly on a Cisco Telepresence System 1300? (Choose three)

The table configuration is completed by using the Cisco Telepresence System administration WebGUI hardware setup The table selection is completed in the Cisco Unified Communications Manager device configuration page The table edge where participants sit is six to ten feet away from the display The table must be perfectly centered and parallel to the Cisco TelePresence System The table edge where participants sit is optimal at ten feet away from the display

Cisco Implementing Cisco TelePresence Installations (ITI) Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Cisco Implementing Cisco TelePresence Installations (ITI) Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner