Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) Set 4

1.

Which action configures transcoding resources in Cisco Unified Communications Manager to function with branch office Cisco IP Phones?

Configure the branch office IP phones with CSS and partitions. Configure the branch office IP phones with MRGs and MRGLs. Configure the branch office IP phones with regions. Configure the branch office IP phones with locations.

2.

What is the purpose of configuring a hardware-based MTP when deploying Cisco Unified Communications Manager?

to allow for supplementary services such as hold, transfer, and conferencing when you need support for up to 24 MTP sessions on the same server and 48 on a separate server when you need the ability to grow support by using DSPs when you want to only use Cisco Unified Communications Manager resources

3.

Which action configures CAC utilizing only Cisco Unified Communications Manager software?

Configure Cisco Unified Communications Manager regions. Configure Cisco Unified Communications Manager locations. Configure Cisco Unified Communications Manager RSVP-enabled locations. Configure Cisco Unified Communications Manager MTPs.

4.

Which bandwidth amounts are correct for configuring locations?

8 kb/s for G.729, 64 kb/s for G.711, and 64 kb/s for G.722 8 kb/s for G.729, 64 kb/s for G.711, and 16 kb/s for G.722 64 kb/s for G.729, 64 kb/s for G.711, and 64 kb/s for G.722 8 kb/s for G.729, 8 kb/s for G.711, and 8 kb/s for G.722

5.

Which action configures AAR to route the calls that have been rejected by the gatekeeper CAC through the PSTN?

Configure Cisco IP Phones for AAR. Configure AAR to work with SRST. Configure AAR to work with CTI route points. This configuration is not possible using AAR.

6.

What is a prerequisite of AAR deployment?

You must have a single distributed call processing deployment. Calls must be manually rerouted through the PSTN or other networks when Cisco Unified Communications Manager blocks a call due to insufficient locationbandwidth. Calls must be automatically rerouted through the PSTN or other networks when Cisco Unified Communications Manager blocks a call due to insufficient locationbandwidth. Clustering must be implemented over the WAN. You must have a centralized call processing deployment.

7.

How is the region assigned to a device such as an IP phone?

Regions are assigned directly in the device configuration page. Regions can be assigned only through a device pool. Regions can be assigned either directly on the device configuration page or through the device pool. If both configurations exist, the device pool regionconfiguration takes precedence. Regions can be assigned either directly on the device configuration page or through the device pool. If both configurations exist, the device region configurationtakes precedence.

8.

How can the location setting be modified to resolve poor call quality?

No adjustment to location setting is needed Mark the bandwidth between the locations as unlimited Decrease the audio bandwidth setting Remove the audio bandwidth setting

9.

Cisco Unified border element is configured to support RSVP-based CAC. When is the RSVP path and reservation message sent and received?

Immediately after the call setup message is received and the reservation message is received after H.245 capabilities negotiation is completed. The path and reservation messages are sent and received after the H.245 capabilities negotiation is completed. The path and reservation messages are sent and received immediately after the call setup message is received. The path is setup once the global command call rsvp-sync is configured.

10.

Company A has deployed a VCS Control and is attempting to register a third-party endpoint. The engineer has confirmed that no traffic is being blocked for the endpoint and it is receiving a valid IP address. Which option could be the cause of this registration failure?

Third-party endpoints are not compatible with VCS Control, only with VCS Expressway. Cisco Unified Communications Manager is required in addition to the VCS Control. An incorrect SIP domain is configured on the VCS Control for the endpoint. The VCS Control must be deployed together with VCS Expressway before endpoints can register to either one.

Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) Set 4

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) Set 4

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner