Cisco Composite Set 1

1.

Which statement is true about EBGP?

An internal routing protocol can be used to reach an EBGP neighbor. The next hop does not change when BGP updates are exchanged between EBGP neighbors. A static route can be used to form an adjacency between neighbors. EBGP requires a full mesh.

2.

Which statement is true about 802.1x port-based authentication?

Hosts are required to have a 802.1x authentication client or utilize PPPoE. Before transmitting data, an 802.1x host must determine the authorization state of the switch. RADIUS is the only supported authentication server type. TACACS+ is the only supported authentication server type. If a host initiates the authentication process and does not receive a response, it assumes it is notauthorized.

3.

The command bgp always-compare-med is added to a router configuration. What will this command accomplish?

forces the router to compare metrics of routes from different autonomous systems forces the router to compare the local preference of routes from different autonomous systems forces the router to compare the weight of routes from different autonomous systems forces the router to compare the communities of routes from different autonomous systems

4.

When IP multicast is enabled via PIM, which mode uses the flood and prune method?

PIM sparse-dense Bidir-PIM PIM-RP PIM-DM PIM-SM

5.

Which statement is true concerning 6to4 tunneling?

IPv4 traffic is encapsulated with an IPv6 header. The edge routers can use any locally configured IPv6 address. Hosts and routers inside a 6to4 site will need a special code. An edge router must use IPv6 address of 2002::/16 in its prefix.

6.

What is the cause of jitter?

variable queue delays packet drops transmitting too many small packets compression

7.

Which command will display EIGRP packets sent and received, as well as statistics on hello packets, updates, queries, replies, and acknowledgments?

debug eigrp packets show ip eigrp traffic debug ip eigrp show ip eigrp interfaces

8.

IS-IS Level 1 routers use LSPs for which purpose?

to build a topology database for the local area only to build a topology database for the local and remote areas to build a topology database for remote areas to build a topology database for areas outside the AS to establish adjacency with L1 IS's

9.

In IS-IS routing, which level is used to route between different areas within the same domain?

Level 0 Level 1 Level 2 Level 3

10.

Assuming that VLAN 1 and VLAN 2 traffic is enabled on the above network, what effect will the following command have when entered on port 0/2 on Switch A spanning-tree vlan 1 port-priority 16

VLAN 1 traffic will be blocked on Switch B port 1/1. VLAN 2 traffic will be blocked on Switch B port 1/1. VLAN 2 traffic will be blocked on Switch A port 0/2. VLANs 1 and 2 will be blocked on Switch A port 0/1. VLANs 1 and 2 will be blocked on Switch A port 0/2.

Cisco Composite Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Cisco Composite Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner