Cisco CDCNIS Cisco Data Center Networking Infrastructure Support

1.

The IDSM management-interface IP Address can be configured from which prompt?

Certkiller 3(Config-if)#

Certkiller 3(Config-hos-net)#

Certkiller 3(Config-mgmt)#

Certkiller 3(config)#

2.

What information is displayed when you execute this command on the IDSM? Show settings

The VLANs that are configured for traffic capture The IDSM interface configuration The management IP Address
The VLANs that are configured for management access

3.

Which command enables virtual firewalls on the FWSM?

Mode Context Enable context Enable virtual Mode Multiple

4.

What can you do to obtain faster RPR+ failover?

Decrease the supervisor synchronization interval Disable core dump on both supervisors Minimize the number of entries in the Layer 3 routing tables Use RPR instead of RPR+

5.

What is required when configuring NTP on the IDSM?

Configure the IDSM host access list to allow access to the NTP server Configure an MD5 key Associate the VLAN containing the NTP server with the IDSM management port Add a service account for the NTP service

6.

What is the implication of executing the command failover interface-policy 2 on an FWSM?

The second configured failover interface policy will be applied to the FWSM The configured failover interface policy will be applied to VLAN 2 The FWSM will become active when it fails to receive two consecutive heartbeats from the paired FWSM The FWSM will fail over when more than one VLAN interface fails

7.

The IDSM management-interface IP Address can be configured from which prompt?

Certkiller 3(Config-if)#

Certkiller 3(Config-hos-net)#

Certkiller 3(Config-mgmt)#

Certkiller 3(config)#

8.

How many IDSMs can monitor the same VLAN?

4 8 32 2 1

9.

What information is displayed when you execute this command on the IDSM? Show settings

The VLANs that are configured for traffic capture The IDSM interface configuration The management IP Address The VLANs that are configured for management access

10.

Certkiller .com network is configured as follows:
NetFlow is on for all core switch interfaces
The NAM receives NDE packets from each switch
Reports show aggregate data for all interfaces How would you view data for specific interfaces on a given switch?

Limit the NDE data capture by specifying the VLANs that apply to the interfaces that you want to view Create ACLs on the NAM data ports to filter the NDE traffic Create a custom NDE data source in Cisco Traffic Analyzer and specify the interfaces that you want to view Enable NetFlow only on the interfaces that you want to view

Cisco CDCNIS Cisco Data Center Networking Infrastructure Support

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Cisco CDCNIS Cisco Data Center Networking Infrastructure Support

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner