×
Detail Form
We will send your result on your email id and phone no. please fill detail
1.
What is correct based upon the below display output? MDS_switch#show ips stats tcp interface gigabitethernet
1/1 detail TCP Statistics for port GigabitEthernet1/1 ?.
TCP Active Connections
Local Address Rermote Address State Send-Q Recv-Q
10.23914.2053225 10.2391418965512 ESTABLISH 0 0
10.23914.2053225 10.2391418965514 ESTABLISH 668 0
10.23914.2053225 0.0.0.0.0 LISTEN 0 0
1/1 detail TCP Statistics for port GigabitEthernet1/1 ?.
TCP Active Connections
Local Address Rermote Address State Send-Q Recv-Q
10.23914.2053225 10.2391418965512 ESTABLISH 0 0
10.23914.2053225 10.2391418965514 ESTABLISH 668 0
10.23914.2053225 0.0.0.0.0 LISTEN 0 0
2.
What configuration command enables all discovered storage to be available for iSCSI?
3.
Using Device Manager, how can zoning be enabled between Fibre Channel members in the same VSAN?
4.
What iSCSI virtual target name was dynamically created over interface iscsi 1/1?
5.
What is the main purpose for Loop Initialization Protocol?
6.
Which scenarios require assigning FICON port numbers?
7.
Please view the output, below:
Port-channel 2 is trunking
Port desniption is To 172.22.36.8
Hardware is Fibre Channel
Port WWN is 24:02:00:0c:85:e9:d2:c0
Admin Port mode is E, trunk mode is on
Port mode is TE
Port vsan is 1
Speed is 4 Gbps
Trunk vsans (admin allowed and active) (1,2,3)
Trunk vsans (up) (1,2,3)
fcl/l is trunking
Hardware is Fibre Channel, FCOT is short
Port WWN is 20:01:00:0c:85:e9:d2:c0
Peer Port WWN is 20:09:00:05:30:00:68:5e
Admin Port mode is E,
trunk mode is on
Trunk vsans (admin allowed and active) (4)
Trunk vsans (up) (4)
Two switches are connected by a 21ink port-channel (port-channel 2) and an EISL (fc1/1) command, "channel- group 2 force", what will happen to VSAN 4?
Port-channel 2 is trunking
Port desniption is To 172.22.36.8
Hardware is Fibre Channel
Port WWN is 24:02:00:0c:85:e9:d2:c0
Admin Port mode is E, trunk mode is on
Port mode is TE
Port vsan is 1
Speed is 4 Gbps
Trunk vsans (admin allowed and active) (1,2,3)
Trunk vsans (up) (1,2,3)
fcl/l is trunking
Hardware is Fibre Channel, FCOT is short
Port WWN is 20:01:00:0c:85:e9:d2:c0
Peer Port WWN is 20:09:00:05:30:00:68:5e
Admin Port mode is E,
trunk mode is on
Trunk vsans (admin allowed and active) (4)
Trunk vsans (up) (4)
Two switches are connected by a 21ink port-channel (port-channel 2) and an EISL (fc1/1) command, "channel- group 2 force", what will happen to VSAN 4?
8.
What is the correct order of events for an N-Port to establish a session with a fiber channel switch network?
9.
What is the correct order (from lowest to highest) of the layers of the Fibre Channel protocol? 1 = Physical 2 = Mapping to ULP 3 = Common Services 4 = Signaling Protocol 5 = Encoding/decoding
10.
FCID 0x600000 is not a valid FCID in what interop mode?