Cisco CCIE Data Center Written Set 1

Question - 15 Maximum mark : - 27

Home
All Exams
Cisco CCIE Data Center Written Online Practice Exams
Cisco CCIE Data Center Written Set 1

Assuming the local peer is 10.0.0.1 and the remote peer (configuration not shown) is 10.0.0.2, which of these is used to configure PIM Anycast-RP on a Nexus
7000 switch?
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip pim anycast-rp 2.2.2.2 10.0.0.1
ip pim anycast-rp 2.2.2.2 10.0.0.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4

feature pim
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip pim anycast-rp 10.0.0.1 2.2.2.2
ip pim anycast-rp 10.0.0.2 2.2.2.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4 ✘ interface loopback1ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip pim anycast-rp 2.2.2.2 10.0.0.1
ip pim anycast-rp 2.2.2.2 10.0.0.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4 ✘ feature pimfeature msdp
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip msdp originator-id loopback1
ip msdp peer 10.0.0.2 connect-source loopback1
ip msdp description 10.0.0.2 To 7010-2
ip msdp password 10.0.0.2 mypassword
!
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4 ✘

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

When using Overlay Transport Virtualization (OTV), how do L2 multicast frames traverse the overlay?

The L2 multicast frames are encapsulated in an OTV packet using the configured control-group multicast address for transport ✘ The L2 multicast frames are dropped because multicast cannot be carried across the overlay ✘ The L2 multicast frames are encapsulated in an OTV packet using the configured data-group multicast address for transport ✘ The L2 multicast frames are forwarded natively across the overlay based on their multicast IDs ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

On a Cisco Nexus 7000 Series Switch, what is the purpose of this command?
Switch# config terminal
switch(config)# mac address-table learning-mode conversational vlan 1-10 switch(config)#

Enable conversational learning on FabricPath vlans 1-10 for F-Series module ✘ Enable FabricPath protocol on VLANs 110 ✘ No need for this command as conversational learning is enabled by default for all VLANs. ✘ Enable conversational learning on Classical Ethernet VLAN for F-Series module ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Where is a typical request in the Cisco UCS XML API placed in the data management engine, and, after the request is confirmed, what is updated?

The request is placed in the transactor queue in FIFO order and the management information tree is updated. ✘ The request is placed in the replicator and persistifier and the store is updated. ✘ The request is placed in the data management engine and the application gateway is updated. ✘ The request is placed in the buffer queue and the commit buffer queue is updated. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

By default, what type of SSH server key is generated by Cisco NX-OS Software?

DSA key generated with 512 bits ✘ RSA key generated with 768 bits ✘ RSA key generated with 1024 bits ✘ DSA key generated with 1024 bits ✔ RSA key generated with 2048 bits ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

In a Cisco Nexus 7000 platform configured with GLBP, which GLBP timer can be tuned to prevent unnecessary GLBP state changes during a switchover or ISSU?

GLBP redirect timer ✘ GLBP forwarder pre-empt delay minimum timer ✘ GLBP hold timer ✘ GLBP pre-empt delay minimum timer ✔ GLBP extended hold timer ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Which two statements about a "Virtual PortChannel graceful consistent check" are true?

Graceful consistency check is enabled by default. When graceful consistency check is enabled, only the links on the secondary peer device are suspended. Graceful consistency check is disabled by default, so to enable this feature, use graceful consistency- check command under VPC domain configuration mode. When graceful consistency check is enabled, only the inconsistent VLANs on the secondary peer device are suspended.

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Which attribute is used to pass the user role back to the Nexus when remote AAA is enabled?

Cisco AV-pair ✘ TACACS+ or RADIUS ack frame role attribute ✘ DH-CHAP challenge attribute ✘ privilege level attribute ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Nexus7000# config t
Nexus700(config)# interface 56thernet 2/11
Nexus700(config-if)# switchport mode private-vlan host
Nexus700(config-if)# switchport private-vlan host-association 14 50 Nexus700(config-if)# exit
Nexus700(config)#
What will this command sequence achieve?

associate interface E2/11 to community VLANs 14 and 50 ✘ associate interface E2/11 to secondary VLANs 14 and 50 ✘ associate interface E2/11 to primary VLAN 50 and secondary VLAN 14 ✘ associate interface E2/11 to primary VLAN 14 and secondary VLAN 50 ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

10.

With Cisco NX-OS on a Cisco Nexus platform, which command shows memory usage, total processes, and CPU state?

show memory detailed ✘ show process cpu sorted ✘ show system resources ✘ show hardware capacity ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Prev Next

Congratulations

you have successfully completed the test

Back to Question View Result

Detail Form

We will send your result on your email id and phone no. please fill detail

Name

Email ID Note: Report will be send to the above Email ID

Phone No

Cisco CCIE Data Center Written Set 1

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner