Cisco BCMSN Building Converged Cisco Multilayer Switched Networks Set 3

Question - 15 Maximum mark : - 29

Home
All Exams
Cisco BCMSN Building Converged Cisco Multilayer Switched Networks Online Mock Tests
Cisco BCMSN Building Converged Cisco Multilayer Switched Networks Set 3

During testing of network redundancy in a fully meshed enterprise campus, a problem has been reported. Both distribution multilayer switches are fully configured for redundancy; clients operate normally when the primary
multilayer distribution switch is operating. All clients drop connections outside of their respective access layer group when the primary distribution switch is shut down and the secondary distribution switch is still operational.
Additional information indicates that the secondary distribution switch is able to ping major corporate and Internet locations. Which item would be the best point of troubleshooting for this connectivity issue?

client network configuration ✘ VLAN mapping ✘ inter-switch trunk configuration ✘ UDLD configuration ✔ first-hop redundancy protocol ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

What network information do you need when you plan to implement a VLAN-based solution?

default VLAN information for all unused switch ports ✘ 802.1x configuration parameters ✘ number of IP subnets needed ✘ IP routing protocol information ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You are planning a new VLAN-based network solution. What is one item you should consider when creating your implementation plan as it concerns VLANs?

generic router and switch configuration parameters ✘ end-to-end test plan after all components have been installed and configured ✘ administrator assignments ✘ rollback plan ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

When you create a network implementation VLAN solution, what is one procedure that you should include in your plan?

Perform an incremental implementation of components. ✘ Following the PPDIOO model, implement the entire solution and then test end-to-end to make sure that it isperforming as designed. ✘ Implement trunking of all VLANs to ensure that traffic is crossing the network as needed before performingany pruning of VLANs. ✘ Test the solution on a segmented portion of a lab network prior to rolling out across the entire network. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

What is a critical piece of information that you should have when creating a VLAN-based implementation plan?

approval from senior management ✘ end-user requirements ✘ IEEE 802.1X authentication parameters ✘ a summary implementation plan ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You have just created a new VLAN on your network. What is one step that you should include in your VLAN- based implementation and verification plan?

Verify that different native VLANs exist between two switches for security purposes. ✘ Verify that the VLAN was added on all switches with the use of the show vlan command. ✘ Verify that the switch is configured to allow for trunking on the switch ports. ✘ Verify that each switch port has the correct IP address space assigned to it for the new VLAN. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You have just created a new VLAN on your network. What is one step that you should include in your VLAN- based implementation and verification plan?

Verify that trunked links are configured to allow the VLAN traffic. ✘ Verify that the switch is configured to allow for trunking on the switch ports. ✘ Verify that each switch port has the correct IP address space assigned to it for the new VLAN. ✘ Verify that different native VLANs exist between two switches for security purposes. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You have just created a new VLAN on your network for inter-VLAN routing. What is one step that you should include in your VLAN-based implementation and verification plan?

Verify that different native VLANs exist between two switches for security purposes. ✘ Verify that the switch is configured to allow for trunking on the switch ports. ✘ Verify that each switch port has the proper IP address space assigned to it for the new VLAN. ✘ Verify that the VLAN virtual interface has been correctly created and enabled. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

A switch that is to be added to the production network has been preconfigured (trunks, VLANs, VTP, and STP) and was tested in your lab. After installing the switch into the network, the entire network went down. What might explain what happened?

The new switch happened to be running Cisco Catalyst operating system, while the other network switches

were running Cisco IOS Software. ✘ The configuration revision of the new switch was higher than the configuration revision of the productionVTP domain. ✘ The link costs on the new switch are set to a high value, causing all ports on the new switch to go into aforwarding mode and none into blocking mode, thereby causing a spanning-tree loop. ✘ The ports connecting to the two switches have been configured incorrectly. One side has the commandswitchport mode access and the other switchport mode trunk. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

10.

Which statement correctly describes enabling BPDU guard on an access port that is also enabled for PortFast?

Upon startup, the port transmits 10 BPDUs. If the port receives a BPDU, PortFast and BPDU guard are

disabled on that port and it assumes normal STP operation. ✘ The access port ignores any received BPDU. ✘ If the port receives a BPDU, it is placed into the error-disable state. ✘ BPDU guard is only configured globally and the BPDU filter is required for port-level configuration. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Prev Next

Congratulations

you have successfully completed the test

Back to Question View Result

Detail Form

We will send your result on your email id and phone no. please fill detail

Name

Email ID Note: Report will be send to the above Email ID

Phone No

Cisco BCMSN Building Converged Cisco Multilayer Switched Networks Set 3

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner