Check Point-Security Administration Featuring GAiA R77 (2) Set 3

Question - 15 Maximum mark : - 27

Home
All Exams
Check Point-Security Administration Featuring GAiA R77 (2) Online Practice Exams
Check Point-Security Administration Featuring GAiA R77 (2) Set 3

How can you most quickly reset Secure Internal Communications (SIC) between a Security Management Server and Security Gateway?

From cpconfig on the Gateway, choose the Secure Internal Communication option and retype the activation key. Next, retype the same key in the Gateway object in SmartDashboard and reinitialize Secure Internal Communications (SIC). ✘ Use SmartUpdate to retype the Security Gateway activation key. This will automatically sync SIC to both the Security Management Server and Gateway. ✘ From the Security Management Server's command line, type fw putkey -p . ✘ Run the command fwm sic_reset to reinitialize the Security Management Server Internal Certificate Authority (ICA). Then retype the activation key on theSecurity Gateway from SmartDashboard. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

How can you recreate the Security Administrator account, which was created during initial Management Server installation on GAiA?

Export the user database into an ASCII file with fwm dbexport. Open this file with an editor, and delete the Administrator Account portion of the file. You will be prompted to create a new account. ✘ Type cpm -a, and provide the existing Administrator's account name. Reset the Security Administrator's password. ✘ Launch cpconfig and delete the Administrator's account. Recreate the account with the same name. ✘ Launch SmartDashboard in the User Management screen, and delete the cpconfig administrator. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

The London Security Gateway Administrator has just installed the Security Gateway and Management Server. He has not changed any default settings. As he tries to configure the Gateway, he is unable to connect. Which troubleshooting suggestion will NOT help him?

Check if some intermediate network device has a wrong routing table entry, VLAN assignment, duplex-mismatch, or trunk issue. ✘ Test the IP address assignment and routing settings of the Security Management Server, Gateway, and console client. ✘ Verify the SIC initialization. ✘ Verify that the Rule Base explicitly allows management connections. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

You need to completely reboot the Operating System after making which of the following changes on the Security Gateway? (i.e. the command cprestart is not sufficient.) 1. Adding a hot-swappable NIC to the Operating System for the first time. 2. Uninstalling the R77 Power/UTM package. 3. Installing the R77 Power/UTM package. 4. Re-establishing SIC to the Security Management Server. 5. Doubling the maximum number of connections accepted by the Security Gateway.

3 only ✘ 1, 2, 3, 4, and 5 ✘ 2, 3 only ✘ 3, 4, and 5 only ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

The Security Gateway is installed on GAiA R77 The default port for the Web User Interface is _______.

TCP 18211 ✘ TCP 443 ✘ TCP 4433 ✘ TCP 257 ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Which command displays the installed Security Gateway version?

fw ver ✘ fw stat ✘ fw printver ✘ cpstat ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Which command line interface utility allows the administrator to verify the Security Policy name and timestamp currently installed on a firewall module?

cpstat fwd ✘ fw ver ✘ fw stat ✘ fw ctl pstat ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Suppose the Security Gateway hard drive fails and you are forced to rebuild it. You have a snapshot file stored to a TFTP server and backups of your Security Management Server. What is the correct procedure for rebuilding the Gateway quickly?

Reinstall the base operating system (i.e., GAiA). Configure the Gateway interface so that the Gateway can communicate with the TFTP server. Revert to the stored snapshot image, and install the Security Policy. ✘ Run the command revert to restore the snapshot, establish SIC, and install the Policy. ✘ Run the command revert to restore the snapshot. Reinstall any necessary Check Point products. Establish SIC and install the Policy. ✘ Reinstall the base operating system (i.e., GAia). Configure the Gateway interface so that the Gateway can communicate with the TFTP server. Reinstall anynecessary Check Point products and previously applied hotfixes. Revert to the stored snapshot image, and install the Policy. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Which of the following statements accurately describes the command upgrade_export?

upgrade_export stores network-configuration data, objects, global properties, and the database revisions prior to upgrading the Security Management Server. ✘ Used primarily when upgrading the Security Management Server, upgrade_export stores all object databases and the /conf directories for importing to a newerSecurity Gateway version. ✘ upgrade_export is used when upgrading the Security Gateway, and allows certain files to be included or excluded before exporting. ✘ This command is no longer supported in GAiA. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

10.

What are you required to do before running the command upgrade_export?

Run a cpstop on the Security Gateway. ✘ Run a cpstop on the Security Management Server. ✘ Close all GUI clients. ✘ Run cpconfig and set yourself up as a GUI client. ✔

Answer & Solution Discuss in Board Save for Later

Answer & Solution

Answer: Option B

Solution:

It provides fallback for IE8.

Prev Next

Congratulations

you have successfully completed the test

Back to Question View Result

Detail Form

We will send your result on your email id and phone no. please fill detail

Name

Email ID Note: Report will be send to the above Email ID

Phone No

Check Point-Security Administration Featuring GAiA R77 (2) Set 3

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner