Avaya Ethernet Routing Switch Implementation and Maintenance Set 3

1.

OSPF computes the shortest path to destination subnets, whereas, IS-IS, as used with SPMB works differently. Which parameter does IS-IS use to compute the path?

customer MACs backbone BEB MAC tables VLAN MAC IDs backbone nodal MAC addresses

2.

Config mlt 1 create name "MLT to Core"
Config rmlt 1 add ports 3/8, 4/8
Config mlt 1 add vlan 1
Config mlt 1 perform-tagging enable
ho mlt info 1
To add more links to this MLT setup at a later date, what needs to be provisioned?

Create a new VLAN and add the new VLAN to the MLT. More ports cannot be added because only a total of two can be aggregated to the core device. once the MLT is enabled and working, more ports cannot be added to the link aggregation Associate the new ports to the same settings as the current MLT ports; then add them to the MLT.

3.

A call centre is using the stacks of Ethernet Routing Switches (ERS) 5520-48T-PWR to supply power over Ethernet (PoE) to their IP telephones. Each switch is attached to 48 telephones. The call centre begins operation at 9:00 am each day and they verify that the switch can supply enough power to support each telephone drawing their maximum power for all switches simultaneously. They are using the IP Phone port 10/100 switch. Which statement it is true if all telephones are drawing 13.2 watts simultaneously?

Each switch of supplying full port to all ports with only the AC input Each switch requires an RPSU 15 in addition to AC to supply full power to all ports. RPSU 15 can support four ERS 5520 switches that supply full power to all ports. Each switch can supply full power to all ports while the AC is unavailable if attached to

4.

Which commands will configure the labeled Ethernet ports appropriately?

Config Ethernet 3/1 enable-diffserv true config Ethernet 1/1 access-diffserv true Config Ethernet 3/1 enable-diffserv true config Ethernet 1/1 access-diffserv false Config Ethernet 1/1, 3/1 enable-diffserv true config Ethernet 1/1 access-diffserv true Config Ethernet 3/1 enable-diffserv true
config Ethernet 3/1 access-diffserv true

5.

Auto-negotiation should be enabled on all ports except under which condition?

When there is a mix of 10 Mops and 1 Gbps end servers When there are fiber ports in some end workstations When only the core Pitches support auto-negotiation When there is a mix of R and RS modules in the stack

6.

A technician is configuring the core of a Converged Campus network, and is adding a backup- master configuration to an existing Virtual Router Redundancy Protocol (VRRP) configuration for a VLAN that extends to the edge switches. Which benefit is expected from the addition of backup-master?

reduced traffic on the Inter Switch Trunks (1ST) reduced traffic on the uplink ports redundant default gateways for host devices reduces VRRP hello packets

7.

In the interaction between EAPO17802.1 and the Enterprise Policy Manager (EPM), what is the role EPM in the User-Based Policy (UBP) process?

It passes the user access request to the RADIUS server It authenticates the user request. It opens a port. it applies the required treatment to the access port.

8.

A technician wants to control the routes being added to the routing table from the BGP routing table. Which statement describes how to do this?

BGP filters are applied to all incoming route information. BGP filters are applied only to external route information. Metrics determine which routes are inserted into the routing table, BGP adds all new priority routes to the routing table.

9.

In a multicast campus, when should the PIM interface in passive mode be configured?

When the ERS 8600 is used as an edge switch and is aggregating end users When PIM control traffic must be passed When there are no unicast routing paths When more than one multicast routing protocol is in use

10.

A split Multi-Link Trunking (SMLT) for switch clustering is being configured. Which statement is a configuration requirement for the SMLT?

CP-Limit is configured on edge switch stacks. Neighboring edge switch stacks should be connected to each other via a DMLT connection to addresilient paths in the event of an SMLT failure. Alternate the primary path of the SMLT connection to load balance the switch core. VLANS that are defined on the SMLT are so defined on the MLT that defines the core Inter SwitchTrunks (IST)

Avaya Ethernet Routing Switch Implementation and Maintenance Set 3

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Avaya Ethernet Routing Switch Implementation and Maintenance Set 3

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner