Avaya-Avaya Ethernet Routing Switch Implementation and Maintenance Exam 2 Set 2

1.

Consider four software upgrade events on an Ethernet Routing Switch (ERS) 2500 series switch: 1. Upgrade the software image 2. The System Reboots 3. Backup the binary configuration to a TFTP server 4. Upgrade the boot/diagnostic code, if the new version is available Which sequence of events will correctly upgrade the software?

3.2.4. 1 3.4.2.1 3.2.1.4 1.2.4.3 1.4.2.3

2.

A technician has complied me configuration of an Ethernet Routing (ERS) 5520 to and now must transfer a backup copy of configuration file to server. Which command is used to accomplish this task?

5520.24T-PWR> copy config ftp filename ers5520 config.cfg 5520-24T-PWR# copy config ftp filename ers5520config.cfg 5570-74T PWR# copy config tftp filename ers5520COnfig.cfg 5520-24T-PWR# copy config scp filename ersS520conftg.cfg

3.

A technician has implemented RSMLT edge design. After recovering from power outage some clients could not communicate. It has been stated that only one of the core RSMLT switches has recovered. What should have been done to prevent the loss of communications?

Turn off the hold down timer. Increase the hold up timer to 9999. Clear the peer IP and MAC addresses. Set the VLAN to copy RSMLT into from a similarity configured VLAN.

4.

The attempt to manage an Ethernet Routing Switch (ERS) 8600 using a VRRP address was unsuccessful. What is causing this problem?

The file virtual router identifier is 0. The datacenter interface is set as a critical IP interface. A real IP address is required for management access not a VRRP address. The incorrect MAC offset is configured for the VRRP address.

5.

A technician has installed a license file on the Ethernet routing switch (ERS) 8800 and rebooted, but cannot configure the associated licensed features. it has been determined that license did not load properly at bootup time. Which two must be verified?

The switch is at the current release. The license filename contains valid characters. The license file is stored in the flash directory The appropriate license level has been obtained. The license file has .dat extension.

6.

In a newly installed network the port LED on an Ethernet Routing Switch (ERS) 5500 is amber, not green. What does this mean?

The port is set to operate at 10 Mbps. The port is set to operate at 100 Mbps. It indicates that there is a transmit fault. It indicates that the port is administratively disabled.

7.

One of the switches in the Ethernet Routing Switch (ERS) stacks files and is replaced. The auto unit replacement (AUR) is enabled but the stack is not functioning properly. What is the problem?

The switches in the stack are not identical The stack power was left on during the switch replacement. The switches in the stack are not running the same release of software The stack has two switches with Force Stack disabled.

8.

A technician needs to reboot an Ethernet Routing Switch (ERS) 5000 Series switch with a default configuration. What needs to be done to keep the IP address and stack license?

Boot partial-default Boot-default save-license Boot default-save Boot restore-license

9.

A split multi-link trunking (SMLT) for switch clustering is being configured. Which statement is a configuration requirement for the SMLT?

CP-limit is configured on edge switch stacks Neighboring edge switch stacks should be connected to each other via DMLT connection to addresilient paths in the event of an SMLT failure Alternate the primary path of the SMLT connection to load balance the switch core VLANs that are defied on the SMLT are also defined on the MLT that defines the core IST

10.

A customer needs to install a new Ethernet Routing Switch (ERS) 2550T on the 172.16.5.0/24 network, but does not have a console cable available. Which statement is correct?

The switch will first attempt to use Bootup to acquire an IP address, and if that fails it will assign IP address 192.160.1.1/24 to the switch IP. The customer can set the switch to use the temporary address of 192.168.192.168 by pressing the UserInterface button on the front of the ERS 2550T To communicate with an ERS 2550T the IP address must first be set though the console interface. The customer can connect to the network management Ethernet port which is pre-configured to use the192 168 1 1/24 IP address

Avaya-Avaya Ethernet Routing Switch Implementation and Maintenance Exam 2 Set 2

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

COMPANY

Products

OTHERS

Partner

Avaya-Avaya Ethernet Routing Switch Implementation and Maintenance Exam 2 Set 2

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Answer & Solution

Answer: Option B

Solution:

Congratulations

Detail Form

COMPANY

Products

OTHERS

Partner